Mounting set Engine Tomos 2L / 3L Puch MV / MS / VS / VZ / DS / Etc

∙ Mounting set engine.

Complete set with:

∙ Bolts & Nuts (M8 x 70mm)
∙ Locking strip (to secure the engine mounting block bolts)

Suitable for:

∙ Puch…

Locking Strip Engine Tomos 2L / 3L Puch MV / MS / VS / VZ / DS / Etc

∙ Locking strip.
∙ To secure the engine mounting block bolts.

Suitable for:

∙ Puch VS50.
∙ Puch MS50V.
∙ Puch MV50.
∙ Puch DS50.
∙ Puch…

Bolts set Engine mounting Complete Puch Maxi / Z-one / Manet / Korado / Etc

∙ Mounting set / Bolt set enginemounting.
∙ Complete set to mount the engine to the frame.

Complete set with:

∙ 3x Mounting Bolt.
∙ 3x Mounting…

Silentblock Engine mounting 8mm x 20mm x 17mm Old Model Puch MS50 / VS50

∙ Engine mount silent block / rubber / bushing.
∙ Mounted in the engine mount (6 Required)
∙ A Piece.

Measurements:

∙ Diameters: 8mm x 20mm.
∙…

Frame bolt and nut set stainless steel Puch Maxi S

∙ Frame bolt and nut set.
∙ Stainless steel.

Complete set with:

∙ Allen screws handlebar clamp M6 (Pay attention! For EBR front fork as original and original front fork…

Frame bolt and nut set stainless steel Puch Maxi N

∙ Frame bolt and nut set.
∙ Stainless steel.

Complete set with:

∙ Bolts and nuts front mudgaurd.
∙ Bolts and nuts rear mudguard.
∙ Bolts and nuts rear carrier.
∙…

Tyre pump Chrome suitable for Puch VS50 / MV50 / VZ50 / MS50L / MS50V / Etc

∙ Tyre pump / tire pump / bicycle pump
∙ Suitable for various 2 & 3 Gear Tomos & Puch Models.

Measurements:

∙ Length +/-:35cm
∙ Length pressed…

Overflow tank fuel/oil with bracket Race/Cross universal

∙ Overflow tank.
∙ Overflow tank for fuel or oil.
∙ Mandatory for Race and Cross!
∙ Complete with mounting parts
∙ Small model.
∙ Universal.

Handle bar stop frame replacement Puch Maxi

∙ Handlebar / front fork stop replacement part.
∙ If the original handle bar stop is damaged or broken off, it can be replaced with this new part.
∙ The old handle bar stop should…

Trailer hitch saddle pin attachment universal

∙ Trailer hitch.
∙ Saddle pin attachment.
∙ Universal.

Battery holder 70mm x 47mm x 100mm Universal

∙ Battery / accu holder.
∙ Handy battery holder to mount yourself on the frame, for example.
∙ Make it fit yourself.
∙ 3D Printed.
∙ Black.

Measurements:

∙ Suitable for…

Box Ignition Puch Logo Aluminium Universal

∙ Box ignition.
∙ To cover up the ignition coil, cdi and voltage regulator!
∙ With deep etched Puch Logo on the lid.
∙ Aluminium.
∙ 100x120x65mm.
∙ Hand etched!
∙ Drill the…

Box Ignition POWERED BY HPI Aluminium Universal

∙ Box ignition.
∙ To cover up the ignition coil, cdi and voltage regulator!
∙ With deep etched POWEDERED BY HPI text on the lid.
∙ Aluminium.
∙ 100x120x65mm.
∙ Hand…

Box Ignition POWERED BY MVT Aluminium Universal

∙ Box ignition.
∙ To cover up the ignition coil, cdi and voltage regulator!
∙ With deep etched POWEDERED BY MVT text on the lid.
∙ Aluminium.
∙ 100x120x65mm.
∙ Hand…

Box Ignition POWERED BY PVL Aluminium Universal

∙ Box ignition.
∙ To cover up the ignition coil, cdi and voltage regulator!
∙ With deep etched POWEDERED BY PVL text on the lid.
∙ Aluminium.
∙ 100x120x65mm.
∙ Hand…

Box Ignition with switch Puch Logo Aluminium Universal

∙ Box ignition.
∙ To cover up the ignition coil, cdi and voltage regulator!
∙ Model with 2 lighted switches on the front side, for example to switch the lights on or as…

Box Ignition with switch POWERED BY HPI Aluminium Universal

∙ Box ignition.
∙ To cover up the ignition coil, cdi and voltage regulator!
∙ Model with 2 lighted switches on the front side, for example to switch the lights on…

Box Ignition with switch POWERED BY MVT Aluminium Universal

∙ Box ignition.
∙ To cover up the ignition coil, cdi and voltage regulator!
∙ Model with 2 lighted switches on the front side, for example to switch the lights on…

Box Ignition with switch POWERED BY PVL Aluminium Universal

∙ Box ignition.
∙ To cover up the ignition coil, cdi and voltage regulator!
∙ Model with 2 lighted switches on the front side, for example to switch the lights on…

VDM Racing footpeg plates adjustable

∙ Footpeg plates.
∙ 3 Ways adjustable.
∙ For Race use.
∙ Aluminium.
∙ For example to mount on the race swingarm axle and on the frame.
∙ 2 Pieces.
∙ Universal.

Swingarm Black Powdercoated complete Original! Puch Maxi S∙ Swing arm.
∙ Black Powdercoated.
∙ Complete with mounting parts!
∙ Original Puch part!

*Used swingarm, new powdercoated, new mounting rubber / mounting…

Swingarm White Powdercoated complete Original! Puch Maxi S∙ Swing arm.
∙ White Powdercoated.
∙ Complete with mounting parts!
∙ Original Puch part!

*Used swingarm, new powdercoated, new mounting rubber / mounting…

Swingarm Gold Powdercoated complete Original! Puch Maxi S

∙ Swing arm.
∙ Gold Powdercoated.
∙ Complete with mounting parts!
∙ Original Puch part!

*Used swingarm, new powdercoated, new mounting rubber / mounting…

Swingarm Silver Powdercoated complete Original! Puch Maxi S∙ Swing arm.
∙ Silver Powdercoated.
∙ Complete with mounting parts!
∙ Original Puch part!

*Used swingarm, new powdercoated, new mounting rubber / mounting…

Swingarm Yellow Powdercoated complete Original! Puch Maxi S∙ Swing arm.
∙ Yellow Powdercoated.
∙ Complete with mounting parts!
∙ Original Puch part!

*Used swingarm, new powdercoated, new mounting rubber / mounting…

Swingarm Blue Powdercoated complete Original! Puch Maxi S

∙ Swing arm.
∙ Blue Powdercoated.
∙ Complete with mounting parts!
∙ Original Puch part!

*Used swingarm, new powdercoated, new mounting rubber / mounting…

Swingarm Purple Powdercoated complete Original! Puch Maxi S∙ Swing arm.
∙ Purple Powdercoated.
∙ Complete with mounting parts!
∙ Original Puch part!

*Used swingarm, new powdercoated, new mounting rubber / mounting…

Swingarm Red Powdercoated complete Original! Puch Maxi S∙ Swing arm.
∙ Red Powdercoated.
∙ Complete with mounting parts!
∙ Original Puch part!

*Used swingarm, new powdercoated, new mounting rubber / mounting…

Swingarm Orange Powdercoated complete Original! Puch Maxi S∙ Swing arm.
∙ Orange Powdercoated.
∙ Complete with mounting parts!
∙ Original Puch part!

*Used swingarm, new powdercoated, new mounting rubber / mounting…

Swingarm Sandblasted complete Original! Puch Maxi S∙ Swing arm.
∙ Sandblasted, ready to spray.
∙ Complete with mounting parts!
∙ Original Puch part!

*Used swingarm, sandblasted, new mounting rubber / mounting…

Swingarm set Chrome Sqaure Complete! EBR Puch Maxi S

∙ Swing arm set.
∙ Sqaure model.
∙ Extra wide: Tyre width 2.50 possible!
∙ Chrome, the chrome work may contain small scratches or dents.
∙ EBR.

Complete set…

Swingarm Chrome Sqaure EBR Puch Maxi S∙ Swingarm.
∙ Sqaure model.
∙ Extra wide: Tyre width 2.50 possible!
∙ Chrome, the chrome work may contain small scratches or dents.
∙ EBR.

Suitable for:

∙ Puch Maxi S Models…

Swingarm Black Sqaure EBR Puch Maxi S∙ Swingarm.
∙ Sqaure model.
∙ Extra wide: Tyre width 2.50 possible!
∙ Black.
∙ EBR.

Suitable for:

∙ Puch Maxi S Models (Model with shock absorbers)
∙ Puch X30 Models.

VDMRacing Swingarm Blank complete Disc brake Top-Qaulity! Puch Maxi S

∙ Swingarm.
∙ Top-Qaulity!
∙ Suitable for Race and Cross use.
∙ Fits plug&play with a Puch five star wheel.
∙ VDMRacing!

*Comes on the axle of the…

VDMRacing Swingarm Black Powdercoated Top-Qaulity! Puch Maxi S

∙ Swingarm.
∙ Black Powdercoated.
∙ Top-Qaulity!
∙ Suitable for Race and Cross use.
∙ Complete with wheel axle, selflocking nut, rings, chain tensiors,…

Swingarm Adjustable Blank VDMRacing Top-Qaulity! Puch Maxi S

∙ Swing arm.
∙ Adjustable shock absorber mounting.
∙ Blank model.
∙ Suitable for Race and Cross use.
∙ Complete with wheel axle, selflocking nut, rings, chain…

Swingarm Blank VDMRacing Top-Qaulity! Puch Maxi S

∙ Swing arm.
∙ Single shock absorber mounting.
∙ Blank model.
∙ Suitable for Race and Cross use.
∙ Complete with wheel axle, selflocking nut, rings, chain tensiors,…

Tube Rectangle Side DIY Swingarm VDMRacing! Puch Maxi S

∙ Tube profile swingarm.
∙ Rectangle model.
∙ DIY, this part can be used to make your own swingarm.
∙ Bare metal.
∙ A Piece (2 required for a swingarm)
∙…

Tube Round Middle DIY Swingarm VDMRacing! Puch Maxi S

∙ Tube profile swingarm.
∙ Round model.
∙ DIY, this part can be used to make your own swingarm.
∙ Placed in the middle between the tube profiles of the swingarm.
∙…

Spacer Front side DIY Swingarm VDMRacing! Puch Maxi S

∙ Spacer bushing Swingarm.
∙ DIY, this part can be used to make your own swingarm.
∙ Placed at the front of the tube profiles of the swingarm.
∙ Bare metal.
∙ A…

Frame Bushing set DIY Swingarm VDMRacing! Puch Maxi S

∙ Frame bush set.
∙ Frame bushing set for mounting a DIY / Race / Cross swingarm.
∙ 2 Pieces (2 required for a swingarm)
∙ VDMRacing!

Measurements:

∙ Outer…

Axle Front side DIY Swingarm VMRacing! Puch Maxi S

∙ Axle Swingarm.
∙ DIY, this part can be used to make your own swingarm.
∙ Placed in the middle between the tube profiles of the swingarm and through the frame.
∙ A Piece…

Mounting bolt DIY Swingarm VDMRacing! Puch Maxi S

∙ Mounting bolt Swingarm axle.
∙ Allen model.
∙ Placed in the axle on the front side of the swingarm through the frame.
∙ A Piece (2 required for a swingarm)
∙…

Mounting plate Shock absorber DIY Swingarm Adjustable VDMRacing! Puch Maxi S

∙ Shock absorber mounting plate.
∙ DIY, this part can be used to make your own swingarm.
∙ Model with 3 mounting holes for the possibility of…

Mounting plate Shock absorber DIY Swingarm VDMRacing! Puch Maxi S

∙ Shock absorber mounting plate.
∙ DIY, this part can be used to make your own swingarm.
∙ Model with 1 mounting hole.
∙ Bare metal.
∙ A Piece (4…

Chain tensioner DIY Swingarm VDMRacing! Puch Maxi S

∙ Chain tensioner.
∙ DIY, this part can be used to make your own swingarm.
∙ Placed in the rear of the swingarm.
∙ Bare metal.
∙ A Piece (2 Required for a…

Mounting plate Chain tensioner DIY Swingarm VDMRacing! Puch Maxi S

∙ Chain tensioner mounting plate.
∙ DIY, this part can be used to make your own swingarm.
∙ Placed on the rear of the swingarm.
∙ Bare metal.
∙ A Piece…

Guide Pin Brake Torque Plate Drum Brake DIY Swingarm VDMRacing! Puch Maxi S

∙ Guide pin brake anchor plate drumbrake.
∙ DIY, this part can be used to make your own swingarm.
∙ Placed on the inside of the swingarm.
∙ Bare…

Guide Pin Brake Torque Plate Disc Brake DIY Swingarm VDMRacing! Puch Maxi S

∙ Guide pin brake anchor discbrake.
∙ DIY, this part can be used to make your own swingarm.
∙ Placed on the inside of the swingarm.
∙ Bare…

Swingarm Black Original! Puch Rough Rider / Magnum X

∙ Swingarm.
∙ Original Puch part!
∙ Black (Small scratches are possible)

Suitable for:

∙ Puch Magnum X.
∙ Puch Rough Rider.

Swingarm Sandblasted Original! Puch Monza / Grand Prix∙ Swing arm.
∙ Sandblasted, ready to spray.
∙ Original Puch part!

*Used swingarm!

Suitable for:

∙ Puch Monza.
∙ Puch Grand Prix.

Swingarm Right side Puch Maxi Plus / Racing∙ Swingarm.
∙ Right side.
∙ A Piece.

Suitable for:

∙ Puch Maxi Plus / Racing.

Swingarm section Original! New Model Tomos 4L / Sprint

∙ Swing arm section.
∙ Right part.
∙ Primer.
∙ For tensioners model half moon.
∙ NOS, Original part!

Suitable for:

∙ Tomos 4L (New models)
∙ Tomos…

Swingarm section Original! Old Model Tomos 4L / Sprint

∙ Swing arm section.
∙ Right part.
∙ Primer.
∙ For tensioners model M7-bolt / nut.
∙ NOS, Original part!

Suitable for:

∙ Tomos 4L (Old models)
∙ Tomos…

Bush swingarm metal 23mm x 28mm x 30mm Puch Z-one / Manet / Korado

∙ Bush / bearing swing arm.
∙ Metal.
∙ A Piece.

Measurements:

∙ Length: 30mm.
∙ Inner diameter: 23mm.
∙ Outer diameter: 28mm.

Suitable for:

∙…

Bearing set swingarm axle Plastic Puch Magnum X

∙ Bearing set swing arm axle.
∙ Plastic.
∙ 2 Pieces.

Suitable for:

∙ Puch Magnum X.

Bearing bush Swingarm Nylon Tomos 4L / APN4 / Sprint / ST50

∙ Bearingbush swingarm.
∙ For the bearing of the swing arm in the frame.
∙ Nylon.
∙ A Piece.

Suitable for:

∙ Tomos 4L.
∙ Tomos APN4.
∙ Tomos Sprint.
∙…

Distance bush Swingarm Nylon Left Tomos 4L

∙ Distancebush.
∙ Placed on the central tube behind the swingarm leftside.
∙ Nylon.
∙ A Piece.

Measurements:

∙ Diameter: 32.5mm - 25.5mm.
∙ Width: 22mm.

Suitable for:

∙…

Mounting plate swingarm Sandblasted Original! Puch Maxi S

∙ Swingarm mountingplate.
∙ For mounting the swingarm in a Puch Maxi S (Original, EBR, MLM swingarm)
∙ Original Puch part!
∙ Sandblasted, ready to spray.

Suitable…

Rubber swingarm Original / EBR / MLM Puch Maxi S

∙ Swingarmrubber.
∙ For mounting the swingarm in a Puch Maxi S (Original, EBR, MLM swingarm)

Suitable for:

∙ Puch Maxi S Models (Model with shock absorbers)

Identical to…

Swingarm mounting bolt set∙ For Original and EBR swingarm.
∙ 4 bolts with washers.

Axle Swingarm M10 x 1mm - 240mm Tomos 2L / 3L / Puch MV / VS / MS

∙ Swing arm axle.
∙ This axle is used in combination with a exhaust mounting plate with a bushing of +/- 40mm length.

Measurements:

∙ Length: 240mm.
∙…

Axle Swingarm M10 x 1mm - 225mm Tomos 2L / 3L / Puch MV / VS / MS

∙ Swing arm axle.
∙ This axle is used in combination with a exhaust mounting plate with a bushing of +/- 25mm length.

Measurements:

∙ Length: 225mm.
∙…

Axle Swingarm M10 x 1mm - 200mm Tomos 2L / 3L / Puch MV / VS / MS

∙ Swing arm axle.

Measurements:

∙ Length: 200mm.
∙ Screw thread: M10 x 1mm.

Suitable for:

∙ Puch MV.
∙ Puch VS.
∙ Puch MS.
∙ Tomos 2L.
∙ Tomos…

Nut Axle Swingarm M10 x 1mm Tomos 2L / 3L / Puch MV / VS / MS

∙ Swing arm axle nut.
∙ Screw thread: M10 x 1mm.

Suitable for:

∙ Puch MV.
∙ Puch VS.
∙ Puch MS.
∙ Tomos 2L.
∙ Tomos 3L.
∙ Etc.

Silentblock Swingarm 14mm x 27mm x 54mm Puch M50 / M50Racing / M125 / Cobra

∙ Swing arm silent block / rubber / bushing.
∙ Mounting in the swingarm at the swingarm axle.
∙ A Piece.

Pay attention ! These silentblocks are…

Silentblock Swingarm 10.5mm x 23mm x 34mm Old Model Puch VZ50 / MC50

∙ Swing arm silent block / rubber / bushing.
∙ Mounted in the swingarm at the swingarm axle.
∙ A Piece.

Measurements:

∙ Diameters: 10.5mm x 23mm.
∙…

Silentblock Swingarm Big 10mm x 22mm x 33mm Tomos 2L / 3L / Puch MV / VS / MS

∙ Swing arm silent block / rubber / bushing.
∙ Big model.
∙ Mounted in the swingarm at the swingarm axle.
∙ A Piece.

Measurements:

∙…

Silentblock Swingarm Small 8mm x 16mm x 17mm Tomos 2L / 3L / Puch MV / VS / MS

∙ Swing arm silent block / rubber / bushing.
∙ Small model.
∙ Mounted in the swingarm at the swingarm axle.
∙ A Piece.

Measurements:

∙…

Silentblock Swingarm 12mm x 25mm x 32mm Puch Monza / VZ50 / MC50 / Grand Prix / N50

∙ Swing arm silent block / rubber / bushing.
∙ Mounting in the swingarm at the swingarm axle.
∙ A Piece.

Measurements:

∙ Diameters:…

Lock set swingarm / front fork Original! Puch Maxi S Royal De Luxe

∙ Lock set swingarm and steering lock.
∙ Original Puch part!
∙ N.O.S, New Old Stock part!

Suitable for:

∙ Puch Maxi S Royal De Luxe.

Swingarm lock Puch MV/VS/Etc

∙ Swingarm lock.
∙ With 2 keys.

Measurements:

∙ Length:193mm.
∙ Outer diameter:10mm.

Suitable for:

∙ Puch MV.
∙ Puch VS.
∙ Etc.

Chain Tensioner M6 Original Fitment! Puch Maxi

∙ Chain tensioner.
∙ Original fitment.
∙ A Piece.

Measurements:

∙ Screw thread: M6.
∙ Diameter axle hole: 12mm.

Suitable for:

∙ Puch Maxi Models.

Chain Tensioner M6 Puch Maxi

∙ Chain tensioner.
∙ A Piece.

Measurements:

∙ Screw thread: M6.
∙ Diameter axle hole: 12mm.

Suitable for:

∙ Puch Maxi Models.

Chain Tensioner M6 Puch Magnum

∙ Chain tensioner.
∙ A Piece.

Measurements:

∙ Screw thread: M6.
∙ Length: 60mm.
∙ Diameter axle hole: 13mm.

SUitable for:

∙ Puch Magnum Models.